Need help?


Search OutdoorKing by entering Key Words Below



Who's Online Now
0 members (), 114 guests, and 96 robots.
Key: Admin, Global Mod, Mod
Online Spare Parts


Online Store


Newest Topics
VC160 Motor advice needed
by QSR - 20/04/24 04:37 PM
Victa 24 hubcaps
by NormK - 18/04/24 02:19 PM
G4 Carby????? Advice please :-)
by Return Rider - 16/04/24 11:45 AM
Fuel Hose for Victa
by Dandare - 14/04/24 07:35 PM
Recoil starter for Villiiers Lightweight engine
by Malcolm Arnold - 14/04/24 02:01 PM
Long term storage of engines - best practice?
by N1KK0 - 29/03/24 02:43 PM
1972 victa vc auto drive front wheels
by QSR - 25/03/24 09:10 PM
Topic Replies
VC160 Motor advice needed
by QSR - 20/04/24 06:44 PM
Fuel Hose for Victa
by NormK - 20/04/24 02:02 PM
Recoil starter for Villiiers Lightweight engine
by Malcolm Arnold - 20/04/24 01:29 PM
Scammers
by maxwestern - 20/04/24 11:11 AM
G4 Carby????? Advice please :-)
by maxwestern - 20/04/24 10:15 AM
Victa 24 hubcaps
by maxwestern - 20/04/24 10:02 AM
Robin EC10
by maxwestern - 13/04/24 06:44 PM
Long term storage of engines - best practice?
by maxwestern - 04/04/24 09:47 PM
1972 victa vc auto drive front wheels
by Mowerfreak - 03/04/24 07:53 PM
Victa Plugs
by maxwestern - 03/04/24 06:51 PM
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
#4439 18/10/05 03:16 AM
Joined: Oct 2005
Posts: 3
Mac3216 Offline OP
Novice
I need an illustrated parts catalog.
I bought this unit new a few years ago and never used it. I took it out last weekend and it worked fine. However, this morning the rubber fuel primer bulb was cracked and the saw would not start. How complicated is the replacement of this bulb and where is a good place to get the part? Is there a repair manual that addresses this repiar.

Membership information
#4440 18/10/05 05:20 AM
Joined: Dec 1999
Posts: 5,334
Likes: 30
Repair Junkie
****
Mac3216,
Parts list has been forwarded.

Regards,

Bruce [Linked Image]


Regards,
[Linked Image]

Bruce


Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
#4441 19/10/05 02:15 PM
Joined: Oct 2005
Posts: 3
Mac3216 Offline OP
Novice
Do you have any idea of how hard this repair is? Anything to watch out for when you take the sides apart?

#4442 19/10/05 05:58 PM
Joined: Dec 1999
Posts: 5,334
Likes: 30
Repair Junkie
****
Mac3216,
Have you tried to take the primer off without taking the casing apart. It should have two lugs on it. If you can get a small screw driver (or thin flat metal)on the side to depress the lugs you might not have to pull the saw apart. Have a close look at the parts list that I sent you.

Regards,

Bruce :


Regards,
[Linked Image]

Bruce


Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
#4443 22/10/05 02:14 PM
Joined: Oct 2005
Posts: 3
Mac3216 Offline OP
Novice
Thank you everyone. I was able to pry the bulb out without spliting the case. However, I found that all the fuel line was dry rotted. I did need to take off the left side which was about 8 screws. I could reach everthing I needed from there. The design was pretty straight forward once I got inside. I wasn't sure how far into the fuel tank the return fuel line went so I just left about 1/2" hanging on the inside. I was able to get the parts locally although they were not original replacement parts and 2' of fuel line cost me $4. My total parts expense was about $15. Once again, Thank you for all your help.


Moderated by  Bruce, Mr Davis 

Link Copied to Clipboard
Newest Members
Armstrong, kindkong, Painey, Tas, Justin Phillips
16,784 Registered Users
Forum Statistics
Forums145
Topics12,710
Posts104,597
Members16,784
Most Online2,545
Dec 23rd, 2019
OutdoorKing Showcase
20 Bucks from FB Marketplace
20 Bucks from FB Marketplace
by Return Rider, February 20
Victa Cortina 2 Shed Find
Victa Cortina 2 Shed Find
by Return Rider, January 25
My Rover Baron 45
My Rover Baron 45
by Maxwell_Rover_Baron, April 16
SHOWCASE - Precision Mowers - 2021
SHOWCASE - Precision Mowers - 2021
by CyberJack, April 14
SHOWCASE – Atco Rotary – Paul C - 2020
SHOWCASE – Atco Rotary – Paul C - 2020
by CyberJack, December 28
HOME |CONTACT US
Powered by UBB.threads™ PHP Forum Software 7.7.5
(Release build 20201027)
Responsive Width:

PHP: 7.4.33 Page Time: 0.016s Queries: 24 (0.011s) Memory: 0.6812 MB (Peak: 0.7195 MB) Data Comp: Zlib Server Time: 2024-04-20 23:33:40 UTC
Valid HTML 5 and Valid CSS