Need help?


Search OutdoorKing-Forum by entering Key Words Below



Who's Online Now
0 members (), 10,553 guests, and 631 robots.
Key: Admin, Global Mod, Mod
Newest Topics
Power Blade VS1000. Anyone familiar?
by Widget - 21/11/26 03:54 AM
Villiers Mk2 Midget needs to be serviced
by Szymon - 16/11/26 03:58 PM
Choosing a blower
by Dandare - 15/11/26 02:15 PM
Scott Bonnar 33 Verticutter
by Malcolm Arnold - 14/11/26 10:52 AM
southern cross KX-C for sale?
by Olqualcast - 12/11/26 02:49 PM
Scott Bonnar 45 ID help
by jimmywa - 07/11/26 06:48 PM
Topic Replies
Power Blade VS1000. Anyone familiar?
by Widget - 21/11/26 03:54 AM
Choosing a blower
by Dandare - 17/11/26 09:47 PM
Villiers Mk2 Midget needs to be serviced
by Bruce - 16/11/26 09:36 PM
Scott Bonnar 33 Verticutter
by Malcolm Arnold - 14/11/26 10:52 AM
southern cross KX-C for sale?
by Olqualcast - 12/11/26 02:49 PM
Morrison olympic 600 backlap tips
by midget98 - 12/11/26 01:51 AM
Scott Bonnar 45 ID help
by jimmywa - 08/11/26 12:00 AM
Victa Runs Then Starts To Stall
by Man With Cheese - 07/11/26 11:33 PM
Rover 45 Catcher
by looktall - 03/11/26 07:47 PM
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
#4439 18/10/05 04:16 AM
Joined: Oct 2005
Posts: 3
Novice
I need an illustrated parts catalog.
I bought this unit new a few years ago and never used it. I took it out last weekend and it worked fine. However, this morning the rubber fuel primer bulb was cracked and the saw would not start. How complicated is the replacement of this bulb and where is a good place to get the part? Is there a repair manual that addresses this repiar.

#4440 18/10/05 06:20 AM
Joined: Dec 1999
Posts: 5,451
Likes: 36
Repair Junkie
****
Mac3216,
Parts list has been forwarded.

Regards,

Bruce [Linked Image]


Regards,
[Linked Image]

Bruce


Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
#4441 19/10/05 03:15 PM
Joined: Oct 2005
Posts: 3
Novice
Do you have any idea of how hard this repair is? Anything to watch out for when you take the sides apart?

#4442 19/10/05 06:58 PM
Joined: Dec 1999
Posts: 5,451
Likes: 36
Repair Junkie
****
Mac3216,
Have you tried to take the primer off without taking the casing apart. It should have two lugs on it. If you can get a small screw driver (or thin flat metal)on the side to depress the lugs you might not have to pull the saw apart. Have a close look at the parts list that I sent you.

Regards,

Bruce :


Regards,
[Linked Image]

Bruce


Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
#4443 22/10/05 03:14 PM
Joined: Oct 2005
Posts: 3
Novice
Thank you everyone. I was able to pry the bulb out without spliting the case. However, I found that all the fuel line was dry rotted. I did need to take off the left side which was about 8 screws. I could reach everthing I needed from there. The design was pretty straight forward once I got inside. I wasn't sure how far into the fuel tank the return fuel line went so I just left about 1/2" hanging on the inside. I was able to get the parts locally although they were not original replacement parts and 2' of fuel line cost me $4. My total parts expense was about $15. Once again, Thank you for all your help.


Moderated by  Bruce, Mr Davis 

Link Copied to Clipboard
November
M T W T F S S
1
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30
Newest Members
Kenniffs, Neill M, Peenuke1, Purgeboi69, JackFlyers
18,241 Registered Users
Forum Statistics
Forums144
Topics12,778
Posts106,882
Members18,242
Most Online40,124
Apr 13th, 2026
OutdoorKing Showcase
20 Bucks from FB Marketplace
20 Bucks from FB Marketplace
by Return Rider, February 20
Victa Cortina 2 Shed Find
Victa Cortina 2 Shed Find
by Return Rider, January 25
My Rover Baron 45
My Rover Baron 45
by Maxwell_Rover_Baron, April 16
SHOWCASE - Precision Mowers - 2021
SHOWCASE - Precision Mowers - 2021
by CyberJack, April 14
SHOWCASE – Atco Rotary – Paul C - 2020
SHOWCASE – Atco Rotary – Paul C - 2020
by CyberJack, December 28
HOME |CONTACT US
Powered by UBB.threads™ PHP Forum Software 8.0.1