Need help?


Search OutdoorKing by entering Key Words Below



Who's Online Now
1 members (Dandare), 87 guests, and 79 robots.
Key: Admin, Global Mod, Mod
Online Spare Parts


Online Store


Newest Topics
G4 Carby????? Advice please :-)
by Return Rider - 16/04/24 11:45 AM
Fuel Hose for Victa
by Dandare - 14/04/24 07:35 PM
Recoil starter for Villiiers Lightweight engine
by Malcolm Arnold - 14/04/24 02:01 PM
Long term storage of engines - best practice?
by N1KK0 - 29/03/24 02:43 PM
1972 victa vc auto drive front wheels
by QSR - 25/03/24 09:10 PM
Old Fuel
by AVB - 21/03/24 10:48 PM
Rover ES with vertical pull start and original decals
by MowingManiac - 19/03/24 10:50 AM
Topic Replies
Fuel Hose for Victa
by Dandare - 18/04/24 03:27 AM
G4 Carby????? Advice please :-)
by NormK - 16/04/24 04:08 PM
Recoil starter for Villiiers Lightweight engine
by maxwestern - 14/04/24 09:00 PM
Robin EC10
by maxwestern - 13/04/24 06:44 PM
Long term storage of engines - best practice?
by maxwestern - 04/04/24 09:47 PM
1972 victa vc auto drive front wheels
by Mowerfreak - 03/04/24 07:53 PM
Victa Plugs
by maxwestern - 03/04/24 06:51 PM
Old Fuel
by AVB - 27/03/24 10:51 PM
Rover ES with vertical pull start and original decals
by maxwestern - 21/03/24 08:51 PM
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
#4956 28/04/06 09:23 AM
Joined: Apr 2006
Posts: 30
jamesl Offline OP
Novice
Hi Bruce,

Could you please send me the tune up instructions for this model (I have 32cc). The carby is a Walbro and I could not find Mexico stamped on it anywhere (it only has a stamp 'ET' 'WT434' .. I hope I recorded the number correctly).

I also need to replace the air filter foam. Could you tell me what type of foam to use so I can cut something to size. I believe I should also dampen it in a bit of 2 stroke oil?

After reading through your site I have identified several resolutions to problems I have been having. Thanks for the great site!

Membership information
#4957 28/04/06 09:28 PM
Joined: Dec 1999
Posts: 5,334
Likes: 30
Repair Junkie
****
jamesl,

The settings for the carby are as listed in other posts in this area.

1. Screw in both low & high screws till they bottom.

2. Undo the low screw 1 & 1/4 turns.

3. Undo the high screw 1 turn.

4. Then start the machine and only udjust the low screw until it throttles without much hesitation.

5. The adjust the high screw while the machine is in the high speed position until it peeks then back off 1/8 turn. :Wavey:

If you can't get it to run properly then post again explaining the problem.


Regards,
[Linked Image]

Bruce


Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.

Moderated by  Bruce, Gadge, Mr Davis 

Link Copied to Clipboard
Newest Members
kindkong, Painey, Tas, Justin Phillips, Infus10n
16,783 Registered Users
Forum Statistics
Forums145
Topics12,708
Posts104,578
Members16,783
Most Online2,545
Dec 23rd, 2019
OutdoorKing Showcase
20 Bucks from FB Marketplace
20 Bucks from FB Marketplace
by Return Rider, February 20
Victa Cortina 2 Shed Find
Victa Cortina 2 Shed Find
by Return Rider, January 25
My Rover Baron 45
My Rover Baron 45
by Maxwell_Rover_Baron, April 16
SHOWCASE - Precision Mowers - 2021
SHOWCASE - Precision Mowers - 2021
by CyberJack, April 14
SHOWCASE – Atco Rotary – Paul C - 2020
SHOWCASE – Atco Rotary – Paul C - 2020
by CyberJack, December 28
HOME |CONTACT US
Powered by UBB.threads™ PHP Forum Software 7.7.5
(Release build 20201027)
Responsive Width:

PHP: 7.4.33 Page Time: 0.013s Queries: 18 (0.009s) Memory: 0.6646 MB (Peak: 0.6890 MB) Data Comp: Zlib Server Time: 2024-04-17 19:05:38 UTC
Valid HTML 5 and Valid CSS