|
|
|
0 members (),
136
guests, and
173
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
|
|
|
GXV140
by NormK - 11/05/25 08:21 PM
|
|
|
|
|
|
|
|
|
|
Joined: Mar 2007
Posts: 131
Apprentice level 2
|
Hi bruce got a small peoblem with a vc 160 it has new base and head gasets, new points the condencer, new pistion n rings, Caby has been cleaned.
Now for the problem it Revs very high on run and if u back it off it does nothing but back fire what could the problem be.
Here are my thoghts on what it is not celling right somewhere but is the qustionis where tell me please if im on the right track or is the problem someelse caby is a g3
Thank Adam
Last edited by ADAM; 26/08/07 10:55 PM.
|
|
|
|
|
Joined: Dec 1999
Posts: 5,375 Likes: 34
Repair Junkie
|
Adam, Did you check the top seal? It is easy to do just take off the flywheel and put some fuel between the crankshaft and the allow housing. If the fuel leaks out you will have to pull the motor a part again. I would be checking that first. 
Regards, ![[Linked Image]](https://www.outdoorking-forum.com.au/forum/images/members/mower-monsterw.jpg) Bruce Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
|
|
|
|
|
Joined: Mar 2007
Posts: 131
Apprentice level 2
|
Hi bruce just quick update on this mower changed the motor yet again this motor has good seals but will run but is running like crap. Here is what its doing now takes awhile to start using a drill (240v) u hold the air hose and kill the air flow and runs fine let it go and it runs like its not getting anouth fuel into it so bruce give ur best idear whats is wrong not
P.s no work done ur craby as yet putting a driffrent g3 on tomorrow
Last edited by ADAM; 04/09/07 11:12 PM.
|
|
|
|
|
Joined: Mar 2007
Posts: 131
Apprentice level 2
|
changed craby running like a dream have to rebiuld the other g3
Last edited by ADAM; 05/09/07 08:38 PM.
|
|
|
|
|
Joined: Dec 1999
Posts: 5,375 Likes: 34
Repair Junkie
|
ADAM, Ok it is a carby issue. 1. Did you replace the 'O'ring on the brass jet and clean it? 2. Did you clean out the two holes in the alloy casing? 3. Did you check the float level? 4. Did you check the bottom seal? This is all you need to do to fix your problem.
Regards, Bruce Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
|
|
|
|
|
Joined: Mar 2007
Posts: 131
Apprentice level 2
|
problem fix and mower sold b4 i got it on ebay lol
|
|
|
|
|
Joined: Dec 1999
Posts: 5,375 Likes: 34
Repair Junkie
|
ADAM, What was the problem with the machine?
Regards, Bruce Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
|
|
|
|
|
Joined: Mar 2007
Posts: 131
Apprentice level 2
|
changed the craby to a diffrent craby and it worked have pull the other one down and find out
|
|
|
|
|
Joined: Dec 1999
Posts: 5,375 Likes: 34
Repair Junkie
|
ADAM, That is the easy way out to just change the carby.  Did you clean out the two holes in the body of the carby where the main jet seats into and replace the 'O'ring. Also you need to check the gov gears and reset the vane. Let me know what you find out.
Regards, Bruce Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
|
|
|
|
These Outdoorking Forums have helped Thousands of people in finding answers to their equipment questions.
If you have received help, please consider making a donation to support the on-going running cost of these forums.
|
|
|
Forums145
Topics12,944
Posts106,588
Members17,444
| |
Most Online2,545
Dec 23rd, 2019
|
|
|
|
|
|
