Need help?


Search OutdoorKing by entering Key Words Below



Who's Online Now
1 members (Willy Supercut), 278 guests, and 96 robots.
Key: Admin, Global Mod, Mod
Online Spare Parts


Online Store


Newest Topics
Why is it so?
by NormK - 20/03/25 03:02 PM
GCV160 bogging down
by Gilera - 20/03/25 08:08 AM
Three Rare Masport Mowers
by jackeo21 - 18/03/25 08:11 PM
Jetfast Edger with Briggs 3hp I/C
by Gilera - 18/03/25 09:36 AM
Scott Bonnar 40 Catcher wanted please
by Luna - 17/03/25 02:04 PM
Lth130 Husqvarna - Belt sizes - Help Required
by Steve_2012 - 13/03/25 08:40 AM
Victa governor nozzle
by Zenny - 12/03/25 07:51 PM
Topic Replies
Victa Mustang VC 160 - Mk IV
by NormK - 20/03/25 05:22 PM
Why is it so?
by NormK - 20/03/25 03:02 PM
GCV160 bogging down
by NormK - 20/03/25 09:20 AM
Masport 5HP Rotahoe
by Timk - 20/03/25 08:19 AM
Three Rare Masport Mowers
by jackeo21 - 18/03/25 08:11 PM
Jetfast Edger with Briggs 3hp I/C
by Gilera - 18/03/25 01:36 PM
Scott Bonnar 40 Catcher wanted please
by NormK - 17/03/25 02:27 PM
Honda GVX160
by NormK - 16/03/25 10:00 AM
New ROVER Reel Mowers
by KenMar - 16/03/25 09:01 AM
Victa governor nozzle
by NormK - 15/03/25 10:44 AM
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
#9551 20/09/08 02:33 AM
Joined: Jul 2005
Posts: 6,362
Likes: 10
Deejay Offline OP
Administrator - Master Technician
****
Hi to All,
As you have read in the welcome posts to new members we all love to learn new things and tinker here........The lesson for today is,
Cannon Balls yay
It was necessary to keep a good supply of cannon balls near the cannon on old war ships. But how to prevent them from rolling about the deck was the problem. The best storage method devised was to stack them as a square based pyramid, with one ball on top, resting on four, resting on nine, which rested on sixteen.
Thus, a supply of 30 cannon balls could be stacked in a small area right next to the cannon. There was only one problem -- how to prevent the bottom layer from sliding/rolling from under the others.
The solution was a metal plate with 16 round indentations, called, for reasons unknown, a Monkey. But if this plate were made of iron, the iron balls would quickly rust to it. The solution to the rusting problem was to make them of brass - hence, Brass Monkeys.
Few landlubbers realize that brass contracts much more and much faster than iron when chilled. Consequently, when the temperature dropped too far, the brass indentations would shrink so much that the iron cannon balls would come right off the monkey.
Thus,it was quite literally, cold enough to freeze the balls off a brass monkey. And all this time, you thought that was just a vulgar expression, didn't you? laugh lol!!































Please do not PM me asking for support. Please post your questions in the appropriate forums, as the replies it may receive may help all members, not just the individual member.
Kindest Regards, Darryl grin


Portal Box 6
Deejay #9552 20/09/08 02:47 AM
Joined: Dec 1999
Posts: 5,360
Likes: 34
Repair Junkie
****
Darryl,

Great bit of reading and now I can say the reason for freezing the balls off a brass monkey. good1

Do you have aby others that might interest the members as it would be good reading for the members. cheers2


Regards,
[Linked Image]

Bruce


Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
Bruce #9553 20/09/08 03:35 AM
Joined: Jul 2005
Posts: 6,362
Likes: 10
Deejay Offline OP
Administrator - Master Technician
****
Hey Bruce, This one was sent to me as an e-mail, will speak to the sender and find out if he has any others wink


Please do not PM me asking for support. Please post your questions in the appropriate forums, as the replies it may receive may help all members, not just the individual member.
Kindest Regards, Darryl grin


Deejay #9556 20/09/08 04:19 AM
Joined: Jul 2005
Posts: 6,362
Likes: 10
Deejay Offline OP
Administrator - Master Technician
****
Hi Bruce, have got the info; will put the next one up now, I will put it up in "Joke of the Day"......Maybe it should go in "Off Topics".....what do you think?


Please do not PM me asking for support. Please post your questions in the appropriate forums, as the replies it may receive may help all members, not just the individual member.
Kindest Regards, Darryl grin



Moderated by  Bruce, Deejay 

Link Copied to Clipboard
Forum Donation
These Outdoorking Forums have helped Thousands of people in finding answers to their equipment questions.

If you have received help, please consider making a donation to support the on-going running cost of these forums.

ShoutChat
Comment Guidelines: Do post respectful and insightful comments. Don't flame, hate, spam.
Newest Members
Timk, Johnhenry, MeBob78, Luspost, TamborineRover
17,316 Registered Users
Forum Statistics
Forums145
Topics12,899
Posts106,299
Members17,317
Most Online2,545
Dec 23rd, 2019
OutdoorKing Showcase
20 Bucks from FB Marketplace
20 Bucks from FB Marketplace
by Return Rider, February 20
Victa Cortina 2 Shed Find
Victa Cortina 2 Shed Find
by Return Rider, January 25
My Rover Baron 45
My Rover Baron 45
by Maxwell_Rover_Baron, April 16
SHOWCASE - Precision Mowers - 2021
SHOWCASE - Precision Mowers - 2021
by CyberJack, April 14
SHOWCASE – Atco Rotary – Paul C - 2020
HOME |CONTACT US
Powered by UBB.threads™ PHP Forum Software 7.7.5
(Release build 20201027)
Responsive Width:

PHP: 7.4.33 Page Time: 0.013s Queries: 23 (0.009s) Memory: 0.6812 MB (Peak: 0.7106 MB) Data Comp: Zlib Server Time: 2025-03-20 09:11:38 UTC
Valid HTML 5 and Valid CSS