OutdoorKing Repair Forum Forums Finding and Swapping To Trade Swap: SB Model 45 for gear start parts

Hi Guys,

I have had this Scott Bonnar for a while now and its basically taking up room in my garage. I was thinking of selling it but i would rather it go to someone here who might restore it.

The mower starts and runs well, i have placed a new carby kit through it and changed the oil as well as the air filters.

The person before me placed a brand new clutch pad so the clutch needs a bit of adjusting (unscrewing the clutch pin and moving the clutch to the right) as it is currently engaged at high revs, but that would be its only flaw in terms of mechanics (which is easily fixed). The blades aren't in great shape but they do cut as is atm and the catcher is not original but its heavy duty! (thick plate steel).


With that in mind, i trying to fix a Victa gear start edger which has a sheared flywheel and crankshaft (well the key connecting to the flywheel anyway). And im trying to rebuild a honda GXV120 engine so im looking for either of those parts in exchange (the gxv120 engine or the gear start flywheel and crankshaft in good condition).


I am located in Liverpool, Sydney

Its a damn shame I gave away my gear start tilt-a-cut otherwise I would have given you the whole thing and paid for a courier. One day I will finally land myself a 45

Joe,

You have helped me out before with parts so if your willing to arrange for a courier its yours (with the proviso thet if you do find an tiltacut edger or a gxv120 in the near future i can have it). Also, im pretty sure that the crankshaft and flywheel for the edger is interchangeable with normal gear starts so if you have those parts in a gear start mower it should do (i hope).

Ok cheers, just woke up from an extended afternoon nap, I have a gut feeling the gear start tilt a cut shared the same steel banded flywheel as all the other victa edgers, I can send a complete mower engine, I'll also double check at the farm I know we have some gxv160's not sure about a 120

Also just quickly done a online quote for a courier and it might be prohibitately expensive unless I can fun a cheaper one, one quote was over $470!!!

Hi Joe, there must be a cheaper option than that...maybe a back-load for one of the trucking firms....or maybe rail..... even to Wagga and you could bring your trailer over. It is too good to miss out on Joe.
I'll have the thinking cap on....

I might be able to come up with a way to assist you there, Next time I have a free weekend, I can borrow a car with towball and grab it, then you can get it any time yopu come out to canberra to see me, or next time I'm in to visit either you or Darryl!

That could be good Ty, Darryl and I are going to try one other avenue tomorrow. I have located a gear start tilt a cut, But I need to talk to the right person at the local shop about it.

Hi Joe, just noticed that this engine was manufactured on the 12th August 1988.
With thanks to grumpy, here's some more info:
Here is the illustrated parts list:
http://bsintek.basco.com/BriggsDocumentDisplay/Z6ntACVJ1DajI.pdf
Here is the operator's manual:
http://bsintek.basco.com/BriggsDocumentDisplay/flivAJX-nfBhU7y.pdf

Ty!

not the trailer debacle again! Looking for bearings at 5am after spending all night waiting..


also Joe, i dont mind if you want to swap for a gxv160, it does need to be a self propelled one though, ill even throw some money your way if you want.


Let me know what you want to do mate, the mower is basically yours though.

Argh, I shouldn't post while half asleep, I misread it and typed it wrong, on the farm I have a GX160 or 3, they are a horizontal shaft motor never mind

Anyway I will try and chase up the gear start tilt-a-cut motor, otherwise I could disassemble and post a powertorque tilt-a-cut, from memory it just needs a cleanup and service, the paint is immaculate on it , etc but its hard to sell an edger out here in the farming community.

Mate, if my services are needed, it will be MY trailer this time!!!

no problems Joe,

EIther the motor or the powertorque tiltacut would both be fine (they will both get the job done on starting a new edger :D).

Let me know when you decide which route to go, ill have the mower around waiting for you in either case.

No dramas I will happily take the scotty,

I will try to score the gear start parts over the next week or so but if that fails I will pull apart the p/t tilt a cut enough to put into two parcels and can easily ship them.

Sounds great.

How are we going to get the scotty over to you? how much would shipping end up costing anyways? (will be cheaper than fuel to yass and back?) maybe we can meet somewhere half way and save us some money?

Meeting at yass could work out well, thats only about 3 hours from me and I could pick Darryl up for a joyride as well...

I will put up a couple of pics of my spare tilt a cut in here to see if you like it or not tomorrow when she isnt so dark outside

Wow!! A road trip.....sounds like fun!

waiting on those piccies Joe! (im sure if you say its in good nic then it is).

Sorry mate, I was thinking of that while I was on lunch today, here are some I just took, I will give it a good sevice if you like the look of it then work out a weekend where its good for both of us to meet up

i like the look of it

Thanks for that Joe.

In terms of timing, it might either need to be fairly soon(early sept) or fairly late (mid october onwards)

Well this weekend and next is out for me, but the following one is good for me, and it also gives me a chance to get it fully up and running for you, not that it needs much just a general checkover, and quick service as I used it at the start of the year.

when you say 'following' do you mean the weekend of 15-16 September? let me know so i can figure out if i have anything on. (i don't but the other half has a bazillion friends/cousins etc and there's always someone having some sort of get together or birthday).

hey Joe,

any news on the Weekend of 15-16 of September? are you good to go with the trade on any of those 2 days?

regards,
P.Matic

Either 14/15/16 is good for me (I have a long weekend that week) I am having internet problems as we speak but I will keep an eye on the place on my mobile....

Hi Joe, the 16th (sunday) is my free day. A meetup in Yass around midday would probably be best im guessing? I dont really know Yass so your better off choosing a venue (all i know is the MYass McDonnalds :D)

If you can PM me your contact details we can finalise everything before the weekend.

Also, let me know if you are chasing anything else just in case i have it for some strange reason (although i doubt it, i know you have a huge array of mowers)

All I know if yass is the big service center with mcdonalds, kfc, etc also. I will pm you shortly....

Hi Joe, just to let you know that I will be working on the 16th. We have a Charity fundraiser for the Wagga Mens' Shed that got burnt out earlier this year.