|
1 members (Dandare),
1,733
guests, and
371
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
Anonymous
Unregistered
|
Does anyone have or know where I can get the owners/service manual for this blower. Works well; just need info on how to set up carb to idle better. Thanks.
|
|
|
|
|
Joined: Dec 1999
Posts: 5,434 Likes: 36
Repair Junkie
|
LBA, Because you are not a registered member of the Board I am unable to send information. Regards, Bruce ![[Linked Image]](https://www.outdoorking-forum.com.au/board/biggrin.gif)
Regards, ![[Linked Image]](https://www.outdoorking-forum.com.au/forum/images/members/mower-monsterw.jpg) Bruce Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
|
|
|
|
|
Joined: Aug 2005
Posts: 5
Novice
|
Bruce, I am now a registered member. Tx.
LA
|
|
|
|
|
Joined: Dec 1999
Posts: 5,434 Likes: 36
Repair Junkie
|
LarryAsh, Information you requested has been set. Regards, Bruce
Regards, Bruce Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
|
|
|
|
|
Joined: Aug 2005
Posts: 5
Novice
|
Bruce, thanks a lot. Got em. Is there an owners manual or something on carb adjustment for this unit. It's a small 2 needle affair and I've tried the usual settings off fully closed, but still very hard to start and no-idle. Sparks good, compression good. Have disassembled and blown out carb passages 2x. Thanks.
LA
|
|
|
|
|
Joined: Dec 1999
Posts: 5,434 Likes: 36
Repair Junkie
|
LarryAsh, I want you to have a look at a couple of things. 1. Check the fuel line hose that it does not have any pin holes in it. Also make sure that the line has not got sticky (when you squeeze the line together it does not seperate)this will reduce the fuel flow. 2. Check the fuel filter in the tank and if it is slightly dirty replace DON'T TRY TO CLEAN IT. 3. Then adjust the high needle to 1 turn & low needle to one and a 1/4 turn. This is your base setting. Then you adjust the low setting till you get it to go to high speed without any hesitation then set the high speed to peek and back off 1/8 turn. If this does not work let me know and I will get you to check a few more things. As to a workshop manual I don't have one. Regards, Bruce
Regards, Bruce Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
|
|
|
|
|
Joined: Aug 2005
Posts: 5
Novice
|
Tx Bruce. Will check and try ur suggestions. Fuel line is new, but I have reused filter. I used to start it by pulling thru numerous times with just the choke, as primer bulb had dry rotted away and I didn't replace that till this year. It would eventually start that way. Now I gotta be sure it's actually priming; I see bubbles moving back to the tank when I push it in (although doubt this is cause of poor idle).
LA
|
|
|
|
|
Joined: Aug 2005
Posts: 5
Novice
|
Bruce, again tx for advice. Working better, but still can't get to idle by itself. Starting a bit easier. I usually run it at full throttle for better engine cooling.
LA
|
|
|
|
|
Joined: Dec 1999
Posts: 5,434 Likes: 36
Repair Junkie
|
LarryAsh,
What is the piston and cylinder like?
Let me know if if either have scratches on them.
Regards,
Bruce
Regards, Bruce Please do not PM me asking for support. Post on the forums as it helps all members not just the individual.
|
|
|
|
|
Joined: Aug 2005
Posts: 5
Novice
|
OK, Bruce. Will advise. LA
LA
|
|
|
|
M |
T |
W |
T |
F |
S |
S |
|
|
|
1
|
2
|
3
|
4
|
5
|
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
|
27
|
28
|
29
|
30
|
31
|
|
|
|
|
Forums144
Topics12,739
Posts106,729
Members18,021
| |
Most Online40,124
Apr 13th, 2026
|
|
|
|
