OutdoorKing Repair Forum Forums Repairs and Maintenance Questions on Chainsaws and Concrete Cutters McCulloch Chainsaws McCulloch Parts

I can supply a wide variety of spare parts for McCulloch Chainsaws & Brushcutters. Just post your request here.

Regards,
Bruce

I am looking for a coil and HT lead for a McCulloch Tivoli 60, is this something you might have?

[This message has been edited by ChrisMcB (edited 13-07-2003).]

ChrisMcB,
Can you supply me the model number for the saw it should start with 600?

Regards,
Bruce

[This message has been edited by Bruce (edited 15-07-2003).]

hi bruce i have a model 60012302 serial 12-078914 eager beaver mcculloch chainsaw im workn on for a customer is there a way to get a parts diagram of this unit somewhere if so please email me cmsmallengines@nistarr.com thanks calvin

A parts list has been forwarded to you.

Regards,
Bruce

Looking for an ignition module for a MAC 3200 chainsaw. The part number is 219848-01 71205. The replacement part number is 302138. Thanks

Looking for the springs that engage the pull starter cogs on a Mc PM 610 saw.

Any help appreciated.

stryder,
I will adise you next week isf the coil is still available.

Regards,
Bruce

tweed,
I need the serial number to send you a parts list so that you can quote the correct part number.

Regards,
Bruce

Bruce,
Thanks for the reply. The serial number for the Mc PM610 is 13-032214.

Again, appreciate your help.

Tweed

Hi
I am after a line trimmer head for my ProMac II brush cutter. Also would like a fuel filter. I am unable to get locally. Can you send me prices for these parts and a spare parts list?

Thanks!!

need some parts available

need mccolluch parts #s 217031
214082-01
216905
need to find out how much each one is thank you and hope to hear from you
calvin

The parts that you require are still available and the prices are:

217031 changes to 300387 Coil $156-00 AUD
214082-01 Carby $207-00 AUD
216905 Air Filter $16-50 AUD

Regards,

Bruce

Hi Bruce, I'm not too sure how to use this BB but I'm looking for a starter reel for a Mac 17. If you can't help, could you suggest a possible source. Thanks, Roy

I have a pulley available and cost $20 + freight.

Regards,

Bruce

Bruce,

I have a McCulloch Mini Pro 35 with a broken starter rewind spring. Can you help?

Cheers.

I am looking for a Chain Oiler for the McCulloch PM610 Model # 60004129

Parts list has been forwarded so that you can quote correct part numbers required.

Regards,

Bruce

I have sent a parts list so that you can quote correct part numbers required.

Regards,

Bruce

Great. Please advise payment details.
cheers,
Roy

[quote]<font face="verdana,arial,helvetica" size="2">Originally posted by Bruce:
[b] I have a pulley available and cost $20 + freight.

Regards,

Bruce

My MAC 3200 fell on the ground and broke the top main handle mounting point. So it looks like I need a new body if such a thing is possible.

Or maybe a suggestion on how to repair it.

Thanks

Bill in Atlanta

Bill,
Parts list has been sent so that you can quote correct part numbers required.

Regards,

Bruce

Hello,
I am in search of an Ignition Coil for a McCulloch line trimmer model B400128-18.

The part # on the coil is 219848-01-60502.

Thank You,
Shawn

Bruce,
Can you email a parts list/diagram for a McCulloch chainsaw model 6000383-16?
Phillip

Phillip Kardenetz

Parts list has been forwarded to you.

Regards,

Bruce

I am looking for bar tightening stud for a
McCulloch Eager Beaver 14" chain saw.

JimV,
Please supply the model number of the saw so that I might help.

Regards,

Bruce

[This message has been edited by Bruce (edited 08-08-2004).]

Re: spare parts for McCulloch Chainsaws.

Hi Bruce,
I have a ProMac 10-10S chainsaw, which has a collapsed big-end bearing.
The remains of the outer race has (as expected) damaged the lower edge of the cylinder, which is resisting the removal of the piston (at least without excessive force).
The piston is scored, as viewed through the port, as will be the cylinder bore.
Other than this failure and the exhaust bolts having fallen out, it is in good condition.
Would this be economical to repair?
Are over-sized pistons available?
And if so, what would be the cost, and range of diameters available?
Thank you.

Regards,
Brad
bradc@maduratea.com.au

Bruce, do you have part for a McCulloch blowers Model mc320 bv.
Regards
Budget

[This message has been edited by Budget (edited 25-08-2004).]

[This message has been edited by Budget (edited 25-08-2004).]

Would you have a pulley for a McCulloch
Mini Mac 25?

Hi Bruce Would you by any chance have a belt Drive Pulley Part No.217505 for McCulloch 7inch cut off sawThanks Joe Brown

Looking for a bow to fit on a 610.

Thanks

Looking for an oiler for a Eager Beaver 3.7.
Model 60013302 Serial number 12-030468. Don't know part number for oiler. Could it be a 219919??Thanks


------------------
jack41tx

jack41tx,
The last time I bought a chain oiler in was 2001. The part number is 219991 that you require but it is expensive. I will have to see if I can get my hands on another one.

Regards,

Bruce

G'day Bruce,
I have a late 70's or early 80's Promac 850 which I believe is a genuine USA model before sell out. It has served me very well for over 20years and still goes like the clappers, but I have not been able to find a manual or parts locally. Can you help?
regards - Davo

davo8,

Below is the Pro Mac 850 parts list.

Hello Bruce,
I need the complete clutch assembley for the McCulloc MiniMac 30. The numbers I can find on it are - Model/serial: 600093 A13-9329. I hope you are able to help.

Bill

Hi can u supply me a walbro sdc carb 44a or something suitable for a mcculloch. Pro mac 700 chainsaw?

Hi Bruce,

Are you able to supply whole carburettor for Mac 3818 chainsaw 11-600038-29. It's either Zama c1q-m36, Walbro wt-774, Zama c1q-m36, c1q-m33. All are interchangeable. Regards Kev
.